Dennis Crawley says:
The diagram below shows how this can be done, by connecting the row/column lines of the keypad to resistors so that each key (the X's in the diagram below) results in a different resistance value. This resistance is connected, along with a load resistor (the 22K shown below), in a voltage divider between Vcc and ground; each key gives a different voltage, thus a different A/D reading.Observations:
- It requires 1% resistors, but it could be tested with normal 20% tolerance.
- It's very stable with voltage fluctuations.
- Since keyboards come with some resistance 80-100 ohms, and they tend to grow, the soft need some calibration as well as keyboard change over the time,...
Basically, the program transmit each key pressed to a terminal, so the programmer can see the key real value. Once he/she *calibrate* the range the pic is ready to use.
;********************************************** LIST P=PIC16F873,F=INHX8M,R=DEC #INCLUDE P16F873.INC __CONFIG _HS_OSC&_WDT_OFF&_CP_OFF&_PWRTE_ON&_BODEN_ON&_LVP_OFF ERRORLEVEL 1,-302 ;********************************************** ;Fosc 16Mhz ;First commented on PicList by Dave Dilatush ;Sat, 9 Feb 2002 20:43:39 GMT ;Re: [PIC]: CHALLENGE: 4x4 keyboard and LCD with 1 port = 8 bits ; ; X-------X-------X-------X----------+--Vcc ; | | | | | ; | | | | | ; X-------X-------X-------X---4.7K---+ ; | | | | | ; | | | | | ; X-------X-------X-------X---10K----+ ; | | | | | ; | | | | | ; X-------X-------X-------X---15K----+ ; | | | | ; | 1.2K 2.4K 3.6K ; | | | | ; +-------+-------+-------+--> To PIC A/D Input ; | ; 22K ; | ; GND ; CBLOCK 0X070 ; BUFFER ; LOOPS ; LOOPS2 ; NIBBLE1 ; NIBBLE2 ; NIBBLE3 ; FILTER1 ; FILTER2 ; FILTER3 ; VECES ; BUFFERKEY ; ENDC ; ORG 00 ; GOTO INIT ; ; ;Delay. @4Mhz-1ms. RETARDO ; MOVWF LOOPS ; TOP2 MOVLW D'110' ; MOVWF LOOPS2 ; TOP NOP ; NOP ; NOP ; NOP ; NOP ; NOP ; DECFSZ LOOPS2 ; GOTO TOP ; DECFSZ LOOPS ; GOTO TOP2 ; RETURN ; ;ADC CONVER BSF ADCON0,GO ; CONSU BTFSC ADCON0,GO ; GOTO CONSU ; RETURN ; ;Resistors and Keys Resistances ;may vary over the time ;so we established ranges for ;each converted value with: ;addlw 255 - Hi ;addlw (Hi - Lo) + 1 ;for a good explanation go to: ;http://www.piclist.com/techref/microchip/rangechk.htm ;********************************; PARSER ; CLRF BUFFERKEY ;Split de hexa into MOVLW .3 ;two nibbles. Test for XORWF FILTER1,W ;Hi nibble, If = 3 BTFSS STATUS,Z ;Test the low nibble GOTO TWO ;otherwise jump. ;3FC ---> real value got it from TOASCII routine MOVFW FILTER2 ; ADDLW 255 - 0X0FE ; ADDLW (0X0FE - 0X0E8)+1 ; MOVLW "1" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;3C4 MOVFW FILTER2 ; ADDLW 255 - 0X0C8 ; ADDLW (0X0C8 - 0X0BF)+1 ; MOVLW "2" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;39E MOVFW FILTER2 ; ADDLW 255 - 0X0A2 ; ADDLW (0X0A2 - 0X09A)+1 ; MOVLW "3" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;363 MOVFW FILTER2 ; ADDLW 255 - 0X067 ; ADDLW (0X067 - 0X05E)+1 ; MOVLW "S" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;345 MOVFW FILTER2 ; ADDLW 255 - 0X049 ; ADDLW (0X049 - 0X041)+1 ; MOVLW "4" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;31F MOVFW FILTER2 ; ADDLW 255 - 0X023 ; ADDLW (0X023 - 0X01B)+1 ; MOVLW "5" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;305 MOVFW FILTER2 ; ADDLW 255 - 0X09 ; ADDLW (0X009 - 0X01)+1 ; MOVLW "6" ; BTFSC STATUS,C ; GOTO SAVEKEY ; TWO ;Values with hi nibble ;equal to 2 ;2DB MOVFW FILTER2 ; ADDLW 255 - 0X0E1 ; ADDLW (0X0E1 - 0XD7)+1 ; MOVLW "U" ;U for UP BTFSC STATUS,C ; GOTO SAVEKEY ; ;2BE MOVFW FILTER2 ; ADDLW 255 - 0X0C2 ; ADDLW (0X0C2 - 0XBA)+1 ; MOVLW "7" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;2A3 MOVFW FILTER2 ; ADDLW 255 - 0X0A7 ; ADDLW (0X0A7 - 0X9F)+1 ; MOVLW "8" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;28E MOVFW FILTER2 ; ADDLW 255 - 0X092 ; ADDLW (0X092 - 0X8A)+1 ; MOVLW "9" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;271 MOVFW FILTER2 ; ADDLW 255 - 0X075 ; ADDLW (0X075 - 0X06D)+1 ; MOVLW "D" ;D for Down BTFSC STATUS,C ; GOTO SAVEKEY ; ;25C MOVFW FILTER2 ; ADDLW 255 - 0X060 ; ADDLW (0X060 - 0X058)+1 ; MOVLW "P" ;P for Program BTFSC STATUS,C ; GOTO SAVEKEY ; ;248 MOVFW FILTER2 ; ADDLW 255 - 0X04C ; ADDLW (0X04C - 0X044)+1 ; MOVLW "0" ; BTFSC STATUS,C ; GOTO SAVEKEY ; ;238 MOVFW FILTER2 ; ADDLW 255 - 0X03C ; ADDLW (0X03C - 0X34)+1 ; MOVLW "B" ;B for Backspace BTFSC STATUS,C ; GOTO SAVEKEY ; ;222 MOVFW FILTER2 ; ADDLW 255 - 0X026 ; ADDLW (0X026 - 0X1E)+1 ; MOVLW "E" ;E for Enter BTFSC STATUS,C ; GOTO SAVEKEY ; KEYBERROR2 ;If some keys have MOVLW "#" ;changed their values SAVEKEY ;the soft could handled MOVWF BUFFERKEY ;the error RETURN ; ;********************************; TOASCII ;When is active, MOVF FILTER1,W ;this routine take the MOVWF NIBBLE1 ;hex value and convert it MOVLW 30H ;into three ascii values ADDWF NIBBLE1 ;Basically check for ;ABCDEF1234567890 MOVF FILTER2,W ; MOVWF BUFFER ; ANDLW 0FH ; MOVWF NIBBLE3 ; MOVLW 0AH ; SUBWF NIBBLE3,0 ; MOVLW 37H ; BTFSS STATUS,C ; MOVLW 30H ; ADDWF NIBBLE3 ; SWAPF BUFFER,0 ; ANDLW 0FH ; MOVWF NIBBLE2 ; MOVLW 0AH ; SUBWF NIBBLE2,0 ; MOVLW 37H ; BTFSS STATUS,C ; MOVLW 30H ; ADDWF NIBBLE2 ; RETURN ; ;********************************;This routine add FILTRO CLRF FILTER1 ;the converted value CLRF FILTER2 ;into 3 registers. CLRF FILTER3 ;256 times. CLRF VECES ;then divide by 256 REPEAT ;ignoring filter3. CALL CONVER ;ex:for 3FB BSF STATUS,RP0 ;filter1=0x003 MOVF ADRESL,W ;filter2=0x0fb BCF STATUS,RP0 ; ADDWF FILTER3,1 ; BTFSS STATUS,C ; GOTO FILT2 ; MOVLW D'1' ; ADDWF FILTER2,1 ; BTFSS STATUS,C ; GOTO FILT2 ; MOVLW D'1' ; ADDWF FILTER1,1 ; FILT2 ; MOVF ADRESH,W ; ADDWF FILTER2,1 ; BTFSC STATUS,C ; INCF FILTER1 ; DECFSZ VECES,1 ; GOTO REPEAT ; ; RETURN ; ; ; ; TRASMI BTFSS PIR1,TXIF ; GOTO TRASMI ; MOVWF TXREG ; NOP ; TRASMI2 BTFSS PIR1,TXIF ;last bit is sent GOTO TRASMI2 ; RETURN ; ;Main INIT BSF STATUS,RP0 ; MOVLW 0FFH ; MOVWF TRISA ; MOVWF TRISB ; MOVLW B'11111111' ; MOVWF TRISC ; MOVLW B'00100110' ; MOVWF TXSTA ; MOVLW D'103' ;16mhz crystal MOVWF SPBRG ;9600bps. If 4mhz is used, MOVLW B'10000010' ;change spbrg to (dec)25 MOVWF ADCON1 ; BCF STATUS,RP0 ; MOVLW B'10000001' ;Fosc/32 MOVWF ADCON0 ; BSF PIR1,TXIF ; BCF PIR1,RCIF ; MOVLW B'10010000' ; MOVWF RCSTA ; ; MOVLW "T" ;welcom screen on pc CALL TRASMI ; MOVLW "X" ; CALL TRASMI ; MOVLW " " ; CALL TRASMI ; MOVLW "O" ; CALL TRASMI ; MOVLW "K" ; CALL TRASMI ; MOVLW D'13' ; CALL TRASMI ; MOVLW D'10' ; CALL TRASMI ; ; ; CICLO ; CALL FILTRO ;check for pushed keys MOVLW 2 ;> than 2 in filter1 SUBWF FILTER1,W ; BTFSS STATUS,C ; GOTO CICLO ; ; MOVLW .83 ;almost 20 ms. CALL RETARDO ;if 4mhz is used, CLRF VECES ;change to (dec)20 CALL FILTRO ; MOVLW 2 ; SUBWF FILTER1,W ; BTFSS STATUS,C ; GOTO CICLO ; ; CALL TOASCII ;un-comment this to see the CALL PARSER ;key real value, so range can RELEASE ;be adjusted CALL FILTRO ;check if key was released MOVLW 0X02 ; SUBWF FILTER1,W ; BC RELEASE ; ; MOVLW ":" ; CALL TRASMI ; MOVFW BUFFERKEY ; CALL TRASMI ; ; MOVFW NIBBLE1 ;un-comment to send keys ; CALL TRASMI ;values to pc screen ; MOVFW NIBBLE2 ; ; CALL TRASMI ; ; MOVFW NIBBLE3 ; ; CALL TRASMI ; MOVLW D'13' ; CALL TRASMI ; MOVLW D'10' ; CALL TRASMI ; ; GOTO CICLO ; ; ENDSee also:
Comments:
file: /Techref/microchip/4x4key1ad7r.htm, 14KB, , updated: 2010/7/8 15:00, local time: 2024/12/25 10:16,
18.191.171.136:LOG IN
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://linistepper.com/techref/microchip/4x4key1ad7r.htm"> PIC Microcontroler 4x4 Keypad with 1 A/D pin</A> |
Did you find what you needed? |