This is file "LCDfg-lite.h".
//==============================================================================
// Copyright (c) 2005-2010, Isaac Marino Bavaresco
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are met:
// * Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
// * Neither the name of the author nor the
// names of its contributors may be used to endorse or promote products
// derived from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE AUTHOR ''AS IS'' AND ANY
// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
// WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
// DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
// DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
// LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
// ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//==============================================================================
// isaacbavaresco@yahoo.com.br
//==============================================================================
// Set TAB width to 4 characters
//==============================================================================
#if !defined __LCD_CFG_H__
#define __LCD_CFG_H__
//==============================================================================
//##############################################################################
//# #
//# THIS FILE IS HEAVILY HARDWARE-DEPENDANT #
//# #
//# IT MUST BE CHANGED TO FIT YOUR BOARD'S CIRCUIT AND CLOCK #
//# #
//##############################################################################
// This version is taylored for my board at 4MHz and Hi-Tech PICC.
// Change this file for your own needs.
//==============================================================================
//
// PIC16F648A
//
// +-----------------U-----------------+
// | |
// LCD_DI <- ==| 1 RA2/AN2/Vref AN1/RA1 18 |== -> LCD_D4
// | |
// LCD_E <- ==| 2 RA3/AN3/CMP1 AN0/RA0 15 |== -> LCD_D5
// | |
// PWRON <- ==| 3 RA4/T0CKI/CMP2 OSC1/RA7 16 |== -> LCD_D6
// | |
// RIGHT -> ==| 4 RA5/!MCLR OSC2/RA6 15 |== -> LCD_D7
// | |
// ==| 5 GND VCC 14 |==
// | |
// <- ==| 6 RB0/INT T1OSI/RB7 13 |== <- UP
// | |
// RXD -> ==| 7 RB1/RX/DT T1CKI/T1OSO/RB6 12 |== <- DOWN
// | |
// TXD <- ==| 8 RB2/TX/CK RB5 11 |== ->
// | |
// LEFT -> ==| 9 RB3/CCP1 RB4 10 |== ->
// | |
// +-----------------------------------+
//
//
//==============================================================================
#include <pic.h>
//==============================================================================
// Define this macro if your board uses the LCD R/!W pin.
//#define USE_READ_PIN
// Define this macro if you want to detect when the LCD is not connected or is
// damaged. Works only if using the R/!W pin.
//#define DETECT_FAILURE
// Number of repetitions before signailng a defective display.
//#define NUMBER_OF_READS_TIMEOUT 2000
// Define this macro if your board uses four bit interface.
#define USE_FOUR_BIT_INTERFACE
//==============================================================================
//==============================================================================
//==============================================================================
//==============================================================================
// Helper macros. Depend on your board.
#define DATAPORT_OUT PORTA
#define DATAPORT_IN PORTA
#define DATAPORT_DIR TRISA
#define LCD_D4 RA1
#define LCD_D5 RA0
#define LCD_D6 RA7
#define LCD_D7 RA6
#define LCD_E RA3
#define LCD_E_DIR TRISA3
#if defined USE_READ_PIN
#define LCD_RW RB6
#define LCD_RW_DIR TRISB6
#endif // defined USE_READ_PIN
#define LCD_DI RA2
#define LCD_DI_DIR TRISA2
//==============================================================================
// These macros depend on the model of your LCD module.
// The size your screen will have at startup.
#define INITIAL_MAXX 16
#define INITIAL_MAXY 2
// The maximum size your screen may have.
#define MAXIMUM_MAXX 16
#define MAXIMUM_MAXY 2
// The usual is 8, but 4 is more useful for such a narrow display.
#define TAB_WIDTH 4
//==============================================================================
// Interrupt-related macros
// If you don't need to disable interrupts, just define them all as empty macros
// The macro 'DeclareIntSaveVar' must declare 's' with a type suitable to hold
// the CPU's current interrupts (enabled/disabled) state
#define DeclareIntSaveVar( s ) unsigned char s
// The macro 'SaveInterruptsState' must save the current interrupts state to 's'
#define SaveInterruptsState( s ) (( s ) = INTCON & 0xc0 )
// The macro 'RestoreInterruptsState' must restore the previous interrupts state
// from 's'
#define RestoreInterruptsState( s ) ( INTCON = INTCON | ( s ))
// The macro 'DisableInterrupts' must disable all interrupts that may interfere
// with the LCD interface (for instance, an interrupt that uses the LCD interface
// pins to scan a keyboard)
#define DisableInterrupts() ( INTCON = INTCON & 0x3f )
//==============================================================================
// Data port manipulation macros
// The macro 'SetDataPortAsInputs' must set the data port bits (4 or 8,
// depending on the used mode) as inputs
#if defined USE_READ_PIN
#define SetDataPortAsInputs() ( DATAPORT_DIR |= 0xc3 )
#else // defined USE_READ_PIN
#define SetDataPortAsInputs()
#endif // defined USE_READ_PIN
// The macro 'SetDataPortAsOutputs' must set the data port bits (4 or 8,
// depending on the used mode) as outputs
#define SetDataPortAsOutputs() ( DATAPORT_DIR &= 0x3c )
// In 8-bit mode, the macro 'ReadDataPortValue' must read all 8 bits of the
// data port to 's', in 4-bit mode it must read the 4 bits of the data
// port to the higher 4 bits of 's'
#define ReadDataPortValue( s ) do \
{ \
s = 0; \
if( LCD_D7 ) s |= 0x80; \
if( LCD_D6 ) s |= 0x40; \
if( LCD_D5 ) s |= 0x20; \
if( LCD_D4 ) s |= 0x10; \
} \
while( 0 )
// In 8-bit mode, the macro 'SetDataPortValue' must output all the 8 bits of 's'
// to the data port, in 4-bit mode it must output the higher 4 bits of 's' to the
// data port
#define SetDataPortValue( s ) do \
{ \
char t; \
t = DATAPORT_OUT & 0x3c; \
if( s & 0x80 ) t |= 0x40; \
if( s & 0x40 ) t |= 0x80; \
if( s & 0x20 ) t |= 0x01; \
if( s & 0x10 ) t |= 0x02; \
DATAPORT_OUT = t; \
} \
while( 0 )
//( DATAPORT_OUT = DATAPORT_OUT & 0xf0 | ((( s ) >> 4 ) & 0x0f ))
// The following macros are only needed if you are using 4-bit interface
#if defined USE_FOUR_BIT_INTERFACE
// The macro 'ReadDataPortValueLow' must read the 4 bits of the data
// port to the lower 4 bits of 's' without disturbing its 4 higher bits.
#define ReadDataPortValueLow( s ) do \
{ \
if( LCD_D7 ) s |= 0x08; \
if( LCD_D6 ) s |= 0x04; \
if( LCD_D5 ) s |= 0x02; \
if( LCD_D4 ) s |= 0x01; \
} \
while( 0 )
// The macro 'SetDataPortValueLow' must output the lower 4 bits of 's' to
// the data port.
#define SetDataPortValueLow( s ) do \
{ \
char t; \
t = DATAPORT_OUT & 0x3c; \
if( s & 0x08 ) t |= 0x40; \
if( s & 0x04 ) t |= 0x80; \
if( s & 0x02 ) t |= 0x01; \
if( s & 0x01 ) t |= 0x02; \
DATAPORT_OUT = t; \
} \
while( 0 )
#endif // defined USE_FOUR_BIT_INTERFACE
//==============================================================================
// Control pins manipulation macros
#if defined USE_READ_PIN
#define SetRWAsRead() ( LCD_RW = 1 )
#define SetRWAsWrite() ( LCD_RW = 0 )
#define SetRWAsOutput() ( LCD_RW_DIR = 0 )
#else // defined USE_READ_PIN
#define SetRWAsRead()
#define SetRWAsWrite()
#define SetRWAsOutput()
#endif // defined USE_READ_PIN
#define SetDIValue( s ) ( LCD_DI = ( s ))
#define SetDIAsData() ( LCD_DI = 1 )
#define SetDIAsInstruction() ( LCD_DI = 0 )
#define SetDIAsOutput() ( LCD_DI_DIR = 0 )
#define SetEAsEnabled() ( LCD_E = 1 )
#define SetEAsDisabled() ( LCD_E = 0 )
#define SetEAsOutput() ( LCD_E_DIR = 0 )
//==============================================================================
void Delay_10us( unsigned short t );
// Delay macros.
#define Delay500ns() asm( "nop" )
// This macro is defined this way (without calling a function) to save call-stack
// levels, because it is used in the deepest function of the package.
// NOTE: The last "nop" is important to prevent the optimizer to optimize the sequence.
#define Delay37us() do \
{ \
asm( "movlw 9" ); \
asm( "addlw -1" ); \
asm( "btfss 3,2" ); \
asm( "goto $-2" ); \
asm( "nop " ); \
} \
while( 0 )
#define Delay100us() Delay_10us( 10 )
// This macro is defined this way (without calling a function) to save call-stack
// levels, because it is used in the deepest function of the package.
// NOTE: The last "nop" is important to prevent the optimizer to optimize the sequence.
#define Delay1520us() do \
{ \
asm( "movlw 254" ); \
asm( "nop " ); \
asm( "nop " ); \
asm( "addlw -1" ); \
asm( "btfss 3,2" ); \
asm( "goto $-4" ); \
asm( "nop " ); \
} \
while( 0 )
#define Delay4100us() Delay_10us( 410 )
#define Delay15ms() Delay_10us( 1500 )
//==============================================================================
// Macro or prototype for the function 'Beep'. Define it as an empty macro if
// your board doesn't have a buzzer or the like.
#define Beep()
//==============================================================================
// This macro defines the name that your 'putc' function must have to be linked
// with the library functions ('printf', etc).
// For MPLAB-C18 it is '_user_putc', for Hi-Tech PICC it is 'putch'.
#define LCD_PUTC putch
//==============================================================================
#endif // !defined __LCD_CFG_H__
//==============================================================================
| file: /Techref/member/IMB-yahoo-J86/lcdcfg-lite.h.htm, 15KB, , updated: 2010/4/25 17:36, local time: 2024/12/28 09:52,
owner: IMB-yahoo-J86,
18.226.169.169:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://linistepper.com/Techref/member/IMB-yahoo-J86/lcdcfg-lite.h.htm"> Routines to control an HD44780-based LCD module emulating a tty screen (lite version)</A> |
| Did you find what you needed? |