please dont rip this site

BusPirate.js

// Buspirate app. 
// http://techref.massmind.org/techref/language/DroidScript/BusPirate/index.htm
// Note: this application only works on devices that support  
// OTG and allow access to external serial devices. 
// 
// Known to work: Nexus7, GalaxyS3/S4, ExperiaZUltra, TescoHudl,  Asus MemoPad 8  
// Don't work: Nexus4, GalaxyS1, AsusMemo

//Global variables. 
var usb=null, reply=""; 
var log="", maxLines;
var txts="", descs=[], cmds=[], ary;
var desc="";
var modes=" HiZ>1-WIRE>UART>I2C>SPI>2WIRE>3WIRE>KEYB>LCD>";
var mode="";
var scaleADC=1;
var aryParm=[];

//Called when application is started. 
function OnStart() { 
    
    txts = app.LoadText("BusPirateCommands");
    if (!txts) { //load default values if none saved.
        txts = "[select commands]\t\r";
        txts +="Help\t?\r";
        txts +="Reset\t#\r";
        txts +="Show Pin State\tv\r";
        txts +="ADC In\td\r";
        txts +="ADC Loop (Voltimeter)\tD\r";
        txts +="Delay 1uS\t&\r";
        txts +="Delay 1mS\t%\r";
        txts +="Frequency Counter\tf\r";
        txts +="Generate #Khz %Duty\tg\r";
        txts +="Control AUX\tc\r";
        txts +="Control /CS\tC\r";
        txts +="AUX/CS low\ta\r";
        txts +="AUX/CS HI\tA\r";
        txts +="AUX/CS In\t@\r";
        txts +="Power off\tw\r";
        txts +="Power ON\tW\r";
        txts +="Pullup Off\tp\r";
        txts +="Pull Bus to VPullup\tP\r";
        txts +="VPullup Pin\te1\r";
        txts +="VPullup 3.3v\te2\r";
        txts +="VPullup 5v\te3\r";
        txts +="HiZ Mode\tm1\r";
        txts +="UART Mode\tm3\r";
        txts +="I2C Mode";
        txts +=" #KHz 1=50 2=100 3=400";
        txts +=" \tm4\r";
        txts +="SPI Mode";
        txts +=" #KHz 1=30 2=125 3=250 4=1000";
        txts +=" #Clock_idle 1=low 2=high";
        txts +=" #Clock_edge 1=idle->active 2=active->ide";
        txts +=" #Phase 1=middle 2=end";
        txts +=" #CS 1=high 2=low";
        txts +=" #Output 1=open_collecter 2=normal";
        txts +=" \tm5\r";
        txts +="1-Wire Mode\tm2\r";
        txts +="2-Wire Mode";
        txts +=" #KHz 1=50 2=50 3=100 4=400";
        txts +=" #Output 1=open_collecter 2=normal";
        txts +=" \tm6\r";
        txts +="3-Wire Mode";
        txts +=" #KHz 1=50 2=50 3=100 4=400";
        txts +=" #CS 1=high 2=low";
        txts +=" #Output 1=open_collecter 2=normal";
        txts +=" \tm7\r";
        txts +="LCD Mode\tm8\r";
        txts +="Bitorder MSB\tl\r";
        txts +="Bitorder LSB\tL\r";
        txts +="HEX Display\to1\r";
        txts +="Decimal Display\to2\r";
        txts +="Binary Display\to3\r";
        txts +="Raw Data\to4\r";
        txts +="Version/Status\ti\r";
        txts +="Clock HI\t/\r";
        txts +="Clock low\t\\\r";
        txts +="Clock Tick\t^\r";
        txts +="Data HI\t-\r";
        txts +="Data low\t_\r";
        txts +="Read bit\t.\r";
        txts +="Clock Tick & Read bit\t!\r";
        txts +="Read Byte\t\r";
        txts +="Bus Start\t[\r";
        txts +="Bus Stop\t]\r";
        txts +="Bus Start w/Read\t{\r";
        txts +="Bus Stop w/Read\t}\r";
        txts +="Repeat #times\t:\r";
        txts +="Search 7-bit I2C addresses\t(1)\r";
        txts +="I2C Sniffer\t(2)\r";
        txts +="List User Macros\t<0>\r";
        txts +="Record As Macro 1\tMACRO\r";
        txts +="Record As Macro 2\tMACRO\r";
        txts +="Record As Macro 3\tMACRO\r";
        txts +="Record As Macro 4\tMACRO\r";
        txts +="Record As Macro 5\tMACRO\r";
        txts +="\t\r";
        }

    ary = txts.split("\r");
    for (var i = 0; i<ary.length; i++) {
        txts = ary[i].split("\t"); //seperate description from command
        cmds[txts[0]]=txts[1]; //associate description with command
        descs[i]=txts[0]; //build ordered array of descriptions
        } 
    
    //Create a layout with objects vertically centered. 
    lay = app.CreateLayout( "linear", "VCenter,FillXY" );    

    //Create title text. 
    txt = app.CreateText("BusPirate"); 
    txt.SetTextSize( 22 ); 
    txt.SetMargins( 0,0,0,0.01 ); 
    lay.AddChild( txt ); 

    //Create a read-only edit box to show responses. 
    edtReply = app.CreateText( "", 0.96, 0.6, "MultiLine,Left,Monospace" ); 
    edtReply.SetMargins( 0,0,0,0.01 ); 
    edtReply.SetBackColor( "#333333" );
    edtReply.SetTextSize( 8 ); // must be 8 to fit pin status
// could be larger for most things. but changing size changes line count.
    lay.AddChild( edtReply ); 
    
    //Create an edit box containing the constructed commands
    edt = app.CreateTextEdit( "", 0.96, 0.2, "NoSpell" ); 
    edt.SetOnChange( edt_OnChange );
    lay.AddChild( edt ); 
    
    //Create program spinner.
    spin = app.CreateSpinner( descs.join(","), 0.8 );
    spin.SetOnTouch( spin_OnTouch );
    lay.AddChild( spin );
    
    //Create a horizontal layout for buttons. 
    layBut = app.CreateLayout("Linear", "Horizontal"); 
    lay.AddChild( layBut ); 

    //Create an connect button. 
    btnConnect = app.CreateButton( "Connect", 0.23, 0.1 ); 
    btnConnect.SetOnTouch( btnConnect_OnTouch ); 
    layBut.AddChild( btnConnect ); 

    //Create an send button. 
    btnSend = app.CreateButton( "Send", 0.23, 0.1 ); 
    btnSend.SetOnTouch( btnSend_OnTouch ); 
    layBut.AddChild( btnSend ); 

     //Create a reset button. 
    btnReset = app.CreateButton( "Reset", 0.23, 0.1 ); 
    btnReset.SetOnTouch( btnReset_OnTouch ); 
    //btnReset.SetOnLongTouch( btnReset_OnLongTouch ); 
    layBut.AddChild( btnReset ); 

    //Create an save button. 
    btnSave = app.CreateButton( "Save", 0.23, 0.1 ); 
    btnSave.SetOnTouch( btnSave_OnTouch ); 
    layBut.AddChild( btnSave); 

    //Add layout to app.     
    app.AddLayout( lay ); 

    } 

//Called when user touches connect button. 
function btnConnect_OnTouch() 
{ 
    //Create USB serial object. 
    usb = app.CreateUSBSerial(); 
    if( !usb ) 
    {
        app.ShowPopup( "Please connect a USB device" );
        return;
    }
    usb.SetOnReceive( usb_OnReceive );
    Send ("i"); //get version / status to start.
    app.ShowPopup( "Connected" );
} 

//Called when user touches send button. 
function btnSend_OnTouch() {  
    //Get rid of blank lines, spaces etc that cause 
    //a problem for Espruino. 
    var s = edt.GetText(); 
    s = s.replace( RegExp("\n\n+","gim"), "\n" ); 
    s = s.replace( RegExp("\n +","gim"), "\n" ); 
    s = s.replace( RegExp("\\)\\s*\\{","gim"), "\)\{" ); 
    s = s.replace( RegExp(", +","gim"), "," ); 
    s = s.replace( RegExp("\\( +","gim"), "\(" ); 
    s = s.replace( RegExp(" +\\)","gim"), "\)" ); 
    edt.SetText(s);

    //Send program to Espruino. 
    Send( s ); 
    } 

//Called when user touches reset button. 
function btnReset_OnTouch() { 
    edt.SetText( "" ); //clear text edit.
    spin.SelectItem(descs[0]); //clear pull down so next selection works
    } 

function btnReset_OnLongTouch() {
    app.SaveText("BusPirateCommands",""); //clear the previously stored data
    }    
    
//Called when user touches save button. 
function btnSave_OnTouch(item) { 
    //need to ask the user for a description for the current command
    //Create dialog window.
    dlgTxt = app.CreateDialog( "Name?" );
    
    //Create a layout for dialog.
    layDlg = app.CreateLayout( "linear", "VCenter,FillXY" );
    layDlg.SetPadding( 0.02, 0, 0.02, 0.02 );
    dlgTxt.AddLayout( layDlg );

    //Create an text edit box.
    edtDesc = app.CreateTextEdit( "Do: "+edt.GetText(), 0.8, 0.1 );
    edtDesc.SetMargins( 0, 0.02, 0, 0 );
    layDlg.AddChild( edtDesc );

    //Create an ok button. 
    btnOk = app.CreateButton( "Ok", 0.23, 0.1 ); 
    btnOk.SetOnTouch( btnOk_OnTouch ); 
    layDlg.AddChild( btnOk ); 
    
    //Show dialog.
    dlgTxt.Show();
    }

//called when user closes save name dialog
function btnOk_OnTouch(item) {
    var txts="";
    desc = edtDesc.GetText();
    descs.push(desc); //add new description to array
    spin.SetList(descs.join(",")); //and to the displayed list
    cmds[desc]=edt.GetText(); //associate command with description
    for (var i=0; i<descs.length; i++) { //build a file to save list
        txts += descs[i]+"\t"+cmds[descs[i]]+"\r";
        }
    //app.SaveText("BusPirateCommands",txts); //and store it.
    dlgTxt.Hide();
    app.ShowPopup("Saved "+desc);
    } 

//Called when text entered directly in edit area
function edt_OnChange() {
    if ("\n"==edt.GetText().slice(-1)) { //if they just pressed return
        edt.SetText( edt.GetText().slice(0,-1) ); //remove the return.
        btnSend_OnTouch(); //pretend the user pressed send
        edt.SetCursorPos( edt.GetText().length ); //move cursor to end
        }
    }

//Called when user touches program spinner.
//http://dangerousprototypes.com/docs/Bus_Pirate_menu_options_guide
function spin_OnTouch( item ) {
    num = item.slice( -1 );
    var s = item;
    var parm = findNextParm(s,0);
    if (parm) { //if there was a parameter marker
        var name = s.slice(0, parm-1); //text before first parm
        var parms=""; //units for the parm
        var aryLay=[]; //an array to hold the lines
        dlgTxt = app.CreateDialog( name ); //make a dialog
        layDlg = app.CreateLayout( "linear", "Vertical,Left" ); //overall
        dlgTxt.AddLayout( layDlg ); 
        while (parm>0) { //for each parmameter
            s = s.slice(parm); //cut off the prior string
            parm = findNextParm(s,0); //go for the next one
            parms = s.slice(0,parm?parm-1:s.length); //to next or end
            //start a new line
            aryLay.push(app.CreateLayout( "linear", "Horizontal,Left") );
            layDlg.AddChild(aryLay[aryLay.length-1]);
            if (parms.indexOf("=")>0) {//list of #=option?
                //Create a spinner to get the unit
                aryParm.push(app.CreateSpinner(parms.split(" ").slice(1), 0.4, 0.07, "Right" ));
                } 
            else {
                //Create an edit box to get the unit
                aryParm.push(app.CreateTextEdit("", 0.4, 0.07, "Number, Right, SingleLine" ));
                }
            aryLay[aryLay.length-1].AddChild(aryParm[aryParm.length-1]);
            //with the name of the unit
            aryLay[aryLay.length-1].AddChild(app.CreateText(parms,0.4,0.07,"Left, Multiline"));
            }
        //Create an ok button. 
        btnParmOk = app.CreateButton( "Ok", 0.23, 0.1 ); 
        btnParmOk.SetOnTouch( btnParmOk_OnTouch ); 
        layDlg.AddChild( btnParmOk ); 
        //Show dialog.
        dlgTxt.Show();
        } // Done with parameterized items
 
    s = edt.GetText() + cmds[item];
    if ("MACRO" == cmds[item]) {
        s = "<"+num+"="+edt.GetText()+">";
        }
    if ("m3" == cmds[item]) { //UART needs baud, data/parity, stop, polarity, out 
        btnUart_OnTouch();
        }
    if ("D" == cmds[item]) {
        s = "";
        btnMultimeter_OnTouch();
        }
    edt.SetText( s );
    edt.SetCursorPos( s.length ); //move cursor to end of string
    }

//Called when user presses Ok on parameter entry dialog
function btnParmOk_OnTouch() { 
    for(var i=0; i<aryParm.length; i++) { //for each parameter
        //get it's value and append it to what we will send
        edt.SetText(edt.GetText()+" "+aryParm[i].GetText().split("=")[0]);
        aryParm[i] = null;
        }
    aryParm = []; //clear it for next time
    dlgTxt.Hide(); //hope that garbage collects... nope

    }

//helper to find either # or % in the parameter description
function findNextParm(item, start) {
    var lb=item.indexOf("#",start)+1, per = item.indexOf("%",start)+1;
    if ( (lb) + (per) > 0 ) { //if we found any parameter markers
        if (lb) {if (per && (per<lb)) return per; else return lb; }
        if (per) {if (lb && (lb<per)) return lb; else return per; }
        }
    return 0;
    }


//called when the user selects UART mode
function btnUart_OnTouch() {  
    var txt="";
    dlgTxt = app.CreateDialog( "UART mode" );
        
    //Create a layout for dialog.
    layDlg = app.CreateLayout( "linear", "Vertical,Left" );
    //layDlg.SetPadding( 0.02, 0, 0.02, 0.02 );
    dlgTxt.AddLayout( layDlg );
    layDlgL1 = app.CreateLayout( "linear", "Horizontal,Left" );
    layDlg.AddChild(layDlgL1);
    //Create baud spinner.
    txt ="1. 300,2. 1200,3. 2400,4. 4800,5. 9600,6. 19200,7. 38400,";
    txt+="8. 57600,9. 115200"
    spinBaud = app.CreateSpinner(txt , 0.4 );
    layDlgL1.AddChild( spinBaud );
        
    //Create data/parity spinner
    UartDP =["None 8","Even 8","Odd 8","None 9"];
    spinDP = app.CreateSpinner(UartDP.join(",") , 0.3 );
    layDlgL1.AddChild( spinDP );
        
    //Create stop bits spinner
    spinSB = app.CreateSpinner("1 ,2 " , 0.2 );
    layDlgL1.AddChild( spinSB );
    
    //Create polarity spinner
    spinP = app.CreateSpinner("1 Idle 1,2 Idle 0" , 0.4 );
    layDlg.AddChild( spinP );
    
    //Create output spinner
    spinOut = app.CreateSpinner("2 Normal (3.3/GND),1 OC (HiZ/GND)" , 0.6 );
    layDlg.AddChild( spinOut );
    
    //Create an ok button. 
    btnUartOk = app.CreateButton( "Ok", 0.23, 0.1 ); 
    btnUartOk.SetOnTouch( btnUartOk_OnTouch ); 
    layDlg.AddChild( btnUartOk ); 
        
    //Show dialog.
    dlgTxt.Show();
    }


//called when user closes UART setup dialog
function btnUartOk_OnTouch(item) {
    var baud=spinBaud.GetText();
    baud = baud.slice(0,baud.indexOf("."))+" ";
    var DP = spinDP.GetText();
    for (var i=UartDP.length;i>=0;i--) {
        if (DP == UartDP[i]) { DP=(i+1)+" "; break; }
        }
    edt.SetText( "m3 "
        +baud
        +DP
        +spinSB.GetText().slice(0,2) 
        +spinP.GetText().slice(0,2) 
        +spinOut.GetText().slice(0,2) 
        );
    dlgTxt.Hide();
    } 

//called when user selects ADC loop mode (D)
function btnMultimeter_OnTouch() { 
    dlgTxt = app.CreateDialog( "Multimeter mode" );
        
    //Create a layout for dialog.
    layDlg = app.CreateLayout( "linear", "Vertical,Center" );
    dlgTxt.AddLayout( layDlg );

    //Create a read-only edit box to show responses. 
    edtVolts = app.CreateText( "0.00", 0.95, 0.15, "Right, Monospace" ); 
    edtVolts.SetMargins( 0,0,0,0.01 ); 
    edtVolts.SetBackColor( "#333333" );
    edtVolts.SetTextSize( 56 ); 
    layDlg.AddChild( edtVolts );
  
    layDlgHoriz = app.CreateLayout( "Linear", "Horizontal" );
    layDlg.AddChild( layDlgHoriz );
    layDlgHoriz.AddChild( app.CreateText( "Scale:" ) );
    
    spinVolts = app.CreateSpinner( "x1,x5,x10,x25,x50,x100", 0.2 );
    spinVolts.SetOnChange( spinVolts_onTouch );
    layDlgHoriz.AddChild( spinVolts );

    btnScaleCal  = app.CreateButton( "Calibrate", 0.3, 0.1 ); 
    btnScaleCal.SetOnTouch( btnScaleCal_OnTouch ); 
    layDlgHoriz.AddChild( btnScaleCal ); 
    layDlg.AddChild( app.CreateText( "(Calibrate will turn on power supplies!)" ) );
    txtScaleCal = null;

    //Create an ok button. 
    btnMultimeterOk  = app.CreateButton( "Exit", 0.23, 0.1 ); 
    btnMultimeterOk.SetOnTouch( btnMultimeterOk_OnTouch ); 
    layDlg.AddChild( btnMultimeterOk ); 
     
    //Show dialog.
    dlgTxt.Show();
    Send("d");
    }

function btnScaleCal_OnTouch() {
    if (!txtScaleCal) { //if we haven't already entered this mode
        layDlg.mode=mode; //save the starting mode locally
        if ("HiZ>"==mode) { 
            Send("m2");
            app.ShowPopup("No power in HiZ, switching to 1-WIRE");
            }
        Send("W"); //Power UP!
        txtScaleCal = app.CreateText( //teach user to connect scale pot
             "1. Connect +5 volt power and ground across potentiometer\n"
            +"2. Connect ADC to potentiometer wiper\n"
            +"3. Select desired scale\n"
            +"4. Trim potentiometer to show power supply voltage (5 V)\n"
            +"5. Disconnect +5 volt power from potentiometer\n"
            +"6. Connect voltage to be measured\n"
            +"(click Calibrate to close)\n"
            ,0.8, 0.4, "Left, Multiline");
        layDlg.AddChild( txtScaleCal );
        }
    else { //if we are already in calibrate mode, get out
        if ("HiZ>"==layDlg.mode) { 
            Send("m1");
            app.ShowPopup("Switching back to HiZ");
            }
        Send("w"); //Power Down
        layDlg.DestroyChild(txtScaleCal);
        txtScaleCal = null;
        }
    }

function spinVolts_onTouch( item ) {
    scaleADC = item.substring(1); //scale is after the "x"
    }
    
function btnMultimeterOk_OnTouch() { 
    if (txtScaleCal) { //if we are still in calibration mode
        btnScaleCal_OnTouch(); //pretend the user closed it
        }
    layDlg.DestroyChild(edtVolts); //destroy the edit box
    edtVolts = undefined; //and forget it so we don't funnel responses there.
    dlgTxt.Hide(); //hide the dialog
    Send("d"); //one last reading so the user as a record of it.
    }


//Check connection and send data.  
function Send( s ) { 
    if( usb ) usb.Write( s+"\r" ); 
    else app.ShowPopup( "Please connect" ); 
    }

//Called when we get data from the BusPirate
function usb_OnReceive( data ) {
    //if we are in meter mode, display the data
    if (typeof(edtVolts)!='undefined') {
        data += ":V"; //ensure we will have delimeters
        data = parseFloat(data.split(":")[1] .split("V")[0]);
        data = scaleADC*data;
        edtVolts.SetText(data.toPrecision(3)+" V");
        Send("d"); //and repeat
        return;
        }
    //Need to translate tabs into spaces.
    var lines = data.split("\n");
    var line; //line outside for scope so it is retained after loop ends
    for (var l = 0; l < lines.length; l++) {
        line="";
        tabs = lines[l].split("\t");
        for (var i = 0; i < tabs.length-1; i++) {
            line += tabs[i]+("        ").slice(0,8-(tabs[i].length % 8));
            }
        line += tabs[i]; //don't expand the last bit of text.
        if ( l < lines.length - 1 ) line += "\n";
        log += line;
        }
    //last line of returned data could be our mode.
    if (modes.indexOf(line)>0 && mode!=line) {
        mode=line; 
        txt.SetText("BusPirate "+mode);
        }
    //scroll extra lines off the top
    var logLines = log.split("\n");
    //calculate the longest line and set font size accordingly
    var maxChars = 0;
    for (var line in logLines) {
        maxChars = Math.max(maxChars, logLines[line].length);
        }
    //we want 8 point when the line is 80(?ish) and up to 14 point at 10.
    edtReply.SetTextSize(Math.min(16-maxChars/10,14));
    maxLines = edtReply.GetMaxLines()-1;
    logLines = logLines.slice( -maxLines );
    log = logLines.join("\n").toString();
    edtReply.SetText( log );
    }
    


file: /Techref/language/DroidScript/BusPirate/script.htm, 19KB, , updated: 2019/8/4 20:31, local time: 2024/12/25 11:06,
TOP NEW HELP FIND: 
18.116.24.148:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://linistepper.com/Techref/language/DroidScript/BusPirate/script.htm"> BusPirate.js</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?